automec_logo

Automec Tiger Stop and Shear Systems

Frontgauge Squaregage Systems

Each drive is built around a heavy duty extrusion that runs the full length of each drive. Support legs are connected directly to this extrusion to bear all weight. A 1/8” thick steel enclosure is added for additional strength.

Studies show that the majority of shearing time is consumed in set-up…not shearing. SQUAGEGAGE reduces that set-up time and increases shear productivity, especially when accurate square blanks are required.

Several cuts can be made on the same blank without putting the piece down. SQUAREGAGE rapidly repositions after each shear cycle with the operator holding the part against the front stops and/or squaring the arm. Oftentimes, the finished blank remains in hand to reduce retrieval time and eliminate material scratching.

Some customers simply use SQUAREGAGE as a go-to gauge for single position cuts.

The typical Squaregage user can usually be identified by large piles of material in front of the shear, and oftentimes two operators. Work pieces are often larger in size so backgauging introduces too much sheet sag. Also, if the dimensions and squareness of the blank are critical, it must be gauged from the front with scrap falling off the back.

Operators often use the Squaregage as a quick go-to gauge although sequential positioning is possible. Angle cutting is also possible.

Square-Gage-Control-Final-png-280x228

CONTROL SPECIFICATIONS

  • All three drives can be programmed independently for angle cutting
  • Slope angle can be programmed in degrees and the software will calculate the position of each drive unit
  • Dimensions can be programmed in Absolute or Incremental for repeating dimensions or patterns
  • All electronics housed in the compact display unit
  • RS 232 interface with software included
  • IN/mm conversion
  • Parts counter
  • 300 job memory
  • 10 cuts per job
  • Jobs can be linked together for larger programs
  • 1 year warranty

PS50 Shearfeed Systems

The operator loads a blank onto PS 50, locks the parts in place with pneumatic grippers, and sets the feed in motion which automatically triggers a shear, punch or stamping machine.

PS 50 advances the material towards the shear blade or punch in increments automatically triggering the secondary machine. When complete, the system retracts for removal and loading of the next piece.

Side-to-side adjustable pneumatic fingers grip the work-piece for feeding. Grippers can be placed up to 5 ft. apart and travel up to 49” front to rear. Gripper can move to within 1” of the punch or shear blade. 3/16” dia. pins on each gripper fit into a corresponding hole on the blank for accurate referencing.

Rugged 1” dual ball screws and (4) ¾” shafts handle the sheet movement. A 1000 watt closed loop D.C. servo motor/amplifier drives the system with speed and precision. Travel is 49”.

Gauging from the front of the device using one reference point on the work-piece eliminates cumulative tolerance buildup experienced with backgauging. All dimensions will be within ± .002” of the original reference.

 

PS 50 utilizes the CNC300 Automec control. It features storage of 300 jobs, shop rugged LED display, and an RS232 computer interface.

The jobs can be set-up on the shop floor and uploaded to the computer for future runs or can be programmed in the office and downloaded to the CNC300.

In either case the operator can easily make changes on CNC300 to correct for minor variations without disturbing the jobs stored in the computer memory.

No programming or tape prep experience is required. The operator simply enters a load position and desired punch or shear dimensions. Once the advance key is depressed the blank is moved into position for the first operation and the shear or punch is activated. When the ram reaches top of stroke the PS 50 advances the material to the next step until the piece is complete. It then returns the grippers to the load position for unloading and loading of the next piece.

Gauging from the device using one reference point on the workpiece eliminates cumulative tolerance buildup experienced with backgauging. All dimensions will tolerance within ± .002” of the original reference.

The operator’s hands are kept free of the punch or shear and reduced handling of the material reduces chance of injury.

ps50_230x178

CONTROL SPECIFICATIONS

  • 300 Jobs (00 to 299)
  • 10 Dimensions per Job (linking available)
  • Programmable Delay (0 – 19 sec.)
  • Calculator to Change Dimensions Incrementally
  • Parts Counter
  • Single Entry Offset
  • RS232 Interface and Software Include
  • .001” Resolution
  • Red L.E.D. Display
  • IN/MM Conversion
  • Tactile Feel Pushbuttons
  • 30 Day Battery Back Up
  • Input Power – 115 VAC ± 10% 50/60 HZ, 7A MAX
  • 11 Digit Job Numbers

Tiger Stop Saw Gear

Tiger Stop

Enter a length and process your part… It’s just that simple!

The TigerStop automatic stop/gauge and pusher system is the perfect addition to almost any machine tool in your shop where ease of setup, ease of use, and accuracy are required. No more battle of the tape measures—every part’s the same with a TigerStop linear measuring system. Employees can be trained in a matter of minutes and be top performers by the end of the day.  Easily installed on most machine tools.

TigerStop’s flagship product with over 30,000 in the field. Its easy to use interface and mechanical design make it suited to any application where you need speed, accuracy and precision.

image006

Built Metal Tough

image008The TigerStop is part of TigerStop’s Built Metal Tough line of products.  These are products with features and durability that metal working shops and plants have come to expect from their equipment.  Does this mean that TigerStop’s Built Metal Tough products are only good for metal applications?  Nah – in fact, they’ll work anywhere you need a tough and durable system to position lots of material quickly and accurately.

Specifications:

image010

* Made in USA from domestic and foreign components.

The truth about part accuracy: Your actual part accuracy will depend on a number of factors outside of TigerStop LLC’s control. This includes but is not limited to condition and type of saw blade, speed of cut, clamping options selected for the machine, material type, material straightness and internal tension of the material, feed speeds, temperature and moisture of the product being cut will all affect your quality and the accuracy of cuts. Also, we have found that there are distinct differences in measuring devices used to validate dimensions of cut parts that can affect apparent accuracy. These factors will affect all cut off systems, regardless of the manufacturer.

image002
 
image004

 

From Framing to Finish and Beyond.
SawGear® is your competitive advantage. Get TigerStop® accuracy and dependability in the shop or on the job site in this highly portable system. SawGear® is easy to setup and easy to use whether you are doing framing, finish or any application where length cutting is needed.

With the Crown+MiterPro™ software, you can quickly and easily do complex finish jobs. Train a novice to cut finish grade crown in a matter of hours.

image006

 


Specifications:

image008

* Made in USA from domestic and foreign components.

The truth about part accuracy: Your actual part accuracy will depend on a number of factors outside of TigerStop LLC’s control. This includes but is not limited to condition and type of saw blade, speed of cut, clamping options selected for the machine, material type, material straightness and internal tension of the material, feed speeds, temperature and moisture of the product being cut will all affect your quality and the accuracy of cuts. Also, we have found that there are distinct differences in measuring devices used to validate dimensions of cut parts that can affect apparent accuracy. These factors will affect all cut off systems, regardless of the manufacturer.

Tiger Stop Tiger Rack

Tiger Stop Tiger Turbo

image002

image004

Accuracy and precision for heavier loads.
TigerRack™ offers precision, accuracy and speed for your industrial applications. TigerRack™’s precision rack and pinion drive system will keep your production humming. Designed for processing tube, bar stock and heavier materials. Have a rough application? TigerRack™s brake system helps guarantee that you don’t end up miscutting parts. Push it, Pull it, Position it. TigerRack™ gets the job done!
image006

Built Metal Tough

image008

TigerRack is part of TigerStop’s Built Metal Tough line of products.  These are products with features and durability that metal working shops and plants have come to expect from their equipment.  Does this mean that TigerStop’s Built Metal Tough products are only good for metal applications?  Nah – in fact, they’ll work anywhere you need a tough and durable system to position lots of material quickly and accurately.

Specifications:

image010

* Made in USA from domestic and foreign components.

The truth about part accuracy: Your actual part accuracy will depend on a number of factors outside of TigerStop LLC’s control. This includes but is not limited to condition and type of saw blade, speed of cut, clamping options selected for the machine, material type, material straightness and internal tension of the material, feed speeds, temperature and moisture of the product being cut will all affect your quality and the accuracy of cuts. Also, we have found that there are distinct differences in measuring devices used to validate dimensions of cut parts that can affect apparent accuracy. These factors will affect all cut off systems, regardless of the manufacturer

image002

image004

If you need speed, TigerTurbo™ can operate at up to 375 feet per minute (114 m/min) with its steel reinforced belt. If pushing capacity is your game, TigerTurbo™ can push 350 lbs (158 Kg) with out rollers or 840 lbs (381 Kg) with roller tables.

image006

Built Metal Tough

image008The TigerTurbo is part of TigerStop’s Built Metal Tough line of products.  These are products with features and durability that metal working shops and plants have come to expect from their equipment.  Does this mean that TigerStop’s Built Metal Tough products are only good for metal applications?  Nah – in fact, they’ll work anywhere you need a tough and durable system to position lots of material quickly and accurately.

Specifications:

image010

* Made in USA from domestic and foreign components.

The truth about part accuracy: Your actual part accuracy will depend on a number of factors outside of TigerStop LLC’s control. This includes but is not limited to condition and type of saw blade, speed of cut, clamping options selected for the machine, material type, material straightness and internal tension of the material, feed speeds, temperature and moisture of the product being cut will all affect your quality and the accuracy of cuts. Also, we have found that there are distinct differences in measuring devices used to validate dimensions of cut parts that can affect apparent accuracy. These factors will affect all cut off systems, regardless of the manufacturer.

Tiger Stop Heavy Duty 2

image002

image004

For your heavy loads, get heavy duty power! The HD2™ offers 2100 lbs (952 Kg) of pushing capacity. When no other machine can push it, pull it, or position it, HD2™’s rack and pinion drive gets the job done.

image006

Built Metal Tough

image008The HeavyDuty2 is part of TigerStop’s Built Metal Tough line of products.  These are products with features and durability that metal working shops and plants have come to expect from their equipment.  Does this mean that TigerStop’s Built Metal Tough products are only good for metal applications?  Nah – in fact, they’ll work anywhere you need a tough and durable system to position lots of material quickly and accurately.

 

Specifications:

image010

* Made in USA from domestic and foreign components.

The truth about part accuracy: Your actual part accuracy will depend on a number of factors outside of TigerStop LLC’s control. This includes but is not limited to condition and type of saw blade, speed of cut, clamping options selected for the machine, material type, material straightness and internal tension of the material, feed speeds, temperature and moisture of the product being cut will all affect your quality and the accuracy of cuts. Also, we have found that there are distinct differences in measuring devices used to validate dimensions of cut parts that can affect apparent accuracy. These factors will affect all cut off systems, regardless of the manufacturer.

Call us today at 972-355-9000

Tiger Stop Systems